How Unbalance Affects Bearing Life

Ahmed M. Al-Abdan, GED/MD, Saudi Electricity Company

Mass unbalance in a rotating system often produces excessive synchronous forces that reduce the life span of various mechanical elements. Unbalance is basically very simple case caused by an asymmetry in the rotating element that results in an offset between the shaft centerline and center of mass (see Figure 1). Asymmetry can be an off-center weight distribution, or it can be a thermal mechanism that produces uneven heating and bowing of the rotor, or it can be an electrical effect that produces uneven magnetic field.

There are many purposes of balancing done to a rotating element. One of that purposes is to reduce the force at the bearings. To eliminate the mass unbalance we have to requalize mass distribution of rotating element around it’s centerline by using add or remove weights from available planes, which will reduce the centrifugal force at the bearings. This can be seen from the following formula:

Where:

Fc: Centrifugal force at bearings (pounds) u: Unbalance weight (ounces) r: Radius of unbalance weight (in) For example, if an unbalance weight of 1.25 ounces is added to a rotor at a 6 inch radius, the resulting force for a rotor turning at 2000 rpm.

An important question to consider is how does this extra 53.1 pounds of force from unbalance affect the life of the bearing? To answer this question, we should define a problem can affect the life of bearings which called fatigue life, many of bearing manufacturer introduce their way to calculate fatigue life i.e. skf by using the following formula.

a: factor for operating condition (Usually between 1.5 and 2.0 Used 1.8) c: rated bearing load (7460 Ibs for this Example) P: actual radial load (395 Ibs for this Example) N: rpm of the machine The calculated L10 life is 101000 hours or about 11.5 years. If the additional unbalance load of 53 pound is added to the radial load (p) of 395 pounds the calculated L10 is reduced to 69253 hours or 7.9 years. The additional 53 pounds of force due to unbalance reduce life by 30%.

OEE: Overall Equipment Effectiveness

Oh "Overall Equipment Effectiveness", I've heard about that before! Unfortunately, in many facilities, that's all OEE (Overall Equipment Effectiveness) is to the personnel. Something they heard of, talked about or read about. Many maintenance departments today still do not effectively utilize the OEE tool even though it's widely used among the world class companies.

What the Pump Was Designed to Do and Why it Doesn't Do it

Contrary to popular opinion, a centrifugal pump is not designed to develop one head at a single capacity as requested by the pump purchaser. In fact a pump is designed and produced to supply a whole range of head-capacity conditions as identified on it’s performance curve. The pump will operate on that curve if it is driven at the particular speed for which the curve is drawn.

What is Wrong with the Modern Centrifugal Pump?

Ask for a modern centrifugal pump recommendation from your favorite supplier and chances are he will recommend one of the standard pump designs that conform to either the A.N.S.I., I.S.O. or D.I.N. specifications. On the surface that might seem like a good recommendation, but the fact is that all of these designs will cause you maintenance problems. Refer to the illustration prior to diving into the details of the obvious problems found within these designs.

Digging Up Savings: Go with the Flow

It's important to find out if material flows are present or not throughout a bulk-processing facility; material cost savings and increased plant efficiency can offset an investment in monitoring. Most bulk solids processors can do this using low-cost acoustic emission-monitoring technology.

Chain Drive Design Recommendations

For optimum chain drive performance the following points should be considered when looking at chain drive design.

Classifying Chemicals to Assure Effective Sealing

The most common question asked by seal salesmen is "what are you sealing?" This is usually followed by asking about shaft size, product, temperature, speed, stuffing box pressure and any other operating conditions they can think of. The problem with this simplistic approach is that you would have to have a very large data bank of information to reference a particular problem so as to be able to make a sensible seal recommendation. There is a much more logical approach to the problem that we will be discussing in the following paragraphs.

A Guide to Matching Electric Motors with Hydraulic Power Units

Sizing electric motors correctly for hydraulic power units can save a sizable amount of money over the life of the equipment. If system pressure and flow are constant, motor sizing simply boils down to the standard equation: hp = QP / 1714EM

How Unbalance Affects Bearing Life