Anatomy of a Hydraulic Pump Failure

Insider Secrets To Hydraulics

I was asked recently to give a second opinion on the cause of a hydraulic pump failure of an axial piston pump. The hydraulic pump failure occured after a short period in service and my client had pursued a warranty claim with the manufacturer. The manufacturer rejected the warranty claim on the basis that the failure had been caused by contamination of the hydraulic fluid. The foundation for this assessment was scoring damage to the valve plate (Figure 1).

Figure 1. Scoring damage to valve plate

How does contamination cause this type of damage to a hydraulic pump?

When hydraulic fluid is contaminated with hard particles that are the same size as the clearance between two lubricated surfaces, a process known as three-body abrasion occurs. Three-body abrasion results in scoring and heavy wear of sliding surfaces (Figure 2).

Figure 2. The process of three-body abrasion

What other explanations are there for this type of damage?

In axial piston designs, the cylinder barrel is hydrostatically loaded against the valve plate. The higher the operating pressure, the higher the hydrostatic force holding the cylinder barrel and valve plate in contact. However, if operating pressure exceeds design limits or if the valve plate is not in proper contact with the cylinder barrel, the cylinder barrel separates from the valve plate. Once separation occurs, the lubricating film is lost, the two surfaces come into contact and a process known as two-body abrasion occurs.

A major clue that the damage to the valve plate was not caused by contamination in this case, is the pattern of wear. Notice that the scoring (bright areas) is confined to the inner and outer edges of the sliding surface of the valve plate (see Figure 1). If the scoring had been caused by three-body abrasion, the damage would be more evenly distributed across the entire surface, with the areas between the pressure kidneys at the top of the picture, likely to exhibit the heaviest damage.

The pattern of wear on the valve plate is consistent with two-body abrasion resulting from uneven contact between the valve plate and cylinder barrel, caused by warping of the valve plate and/or separation. Examination of the sliding surface of the cylinder barrel (Figure 3) supports this assessment. Notice that the scoring of the cylinder barrel is heaviest top right of the picture and lightest bottom left. Examination of the head of the hydraulic pump also revealed uneven contact between the valve plate and head.

Figure 3. Scoring damage to cylinder barrel

Root cause of failure

Although the valve plate was flat, its locating dowel was holding it off the head on one side (center right of Figure 1). This in turn was causing the valve plate to be tilted against the cylinder barrel, resulting in uneven loading, separation and two-body abrasion of the two surfaces. The root cause of this hydraulic pump failure was not contamination; but rather improper assembly at the factory.

Insider Secrets To Hydraulics

Analyzing Semiconductor Failure

Semiconductor devices are almost always part of a larger, more complex piece of electronic equipment. These devices operate in concert with other circuit elements and are subject to system, subsystem and environmental influences. When equipment fails in the field or on the shop floor, technicians usually begin their evaluations with the unit's smallest, most easily replaceable module or subsystem. The subsystem is then sent to a lab, where technicians troubleshoot the problem to an individual component, which is then removed--often with less-than-controlled thermal, mechanical and electrical stresses--and submitted to a laboratory for analysis. Although this isn't the optimal failure analysis path, it is generally what actually happens.

Improvement: What Comes First?

I use the term RCPE because it is a waste of good initiatives and time to only find the root cause of a problem, but not fixing it. I like to use the word problem; a more common terminology is Root Cause Failure Analysis (RCFA), instead of failure because the word failure often leads to a focus on equipment and maintenance. The word problem includes all operational, quality, speed, high costs and other losses. To eliminate problems is a joint responsibility between operations, maintenance and engineering.

An Integrated Process for System Maintenance, Fault Diagnosis and Support

This paper presents an overview of an integrated process for system maintenance, fault diagnosis and support. The solution is based on Qualtech System, Inc.’s (QSI’s) TEAMS toolset for integrated diagnostics and involves several key innovations. As a showcase of the integrated solution, QSI, along with Antech Systems and Carnegie Mellon University (CMU), have recently completed a research project for the Information Technology Branch at the Naval Air Warfare Center–Aircraft Division (NAWC-AD) in St. Inigoes, MD. The entire system, termed ADAPTS (Adaptive Diagnostic And Personalized Technical Support), provides a comprehensive solution to integrated maintenance and training.

Anatomy of a Boiler Failure—A Different Perspective

The power industry’s operating and maintenance practices were held up to intense regulator and public scrutiny when on November 6, 2007, a Massachusetts power plant’s steam-generating boiler exploded and three men died. The Department of Public Safety’s Incident Report investigation determined that the primary cause of the Dominion Energy New England’s Salem Harbor Generating Station Unit 3 explosion was extensive corrosion of boiler tubes

Are We Willing to Hear What “Failure” Has to Say?

Root Cause Analysis has the potential of CHANGING people, IF the leader of the investigation knows of this potential. Far from “just another problem-solving exercise,”the root cause analysis should SLOW PEOPLE DOWN to the extent that they can see the truth of the incident under inquiry, WHATEVER THE TRUTH MIGHT BE. This paper focuses on two parts of our human nature which are large obstacles to root cause discovery, i.e., our unwillingness to slow down, and our unwillingness to let go of certain basic assumptions about life. Warning: This paper is designed to challenge the way you think about Root Cause Analysis.

Definition of Root Cause Analysis (RCA)

A fault tree is constructed starting with the final failure and progressively tracing each cause that led to the previous cause. This continues till the trail can be traced back no further. Each result of a cause must clearly flow from its predecessor (the one before it). If it is clear that a step is missing between causes it is added in and evidence looked for to support its presence. Below is a sample fault tree for the moral story of the kingdom lost because of a missing horseshoe nail.

Anatomy of a Hydraulic Pump Failure